- #Fsuipc prear3d setting how to
- #Fsuipc prear3d setting software
- #Fsuipc prear3d setting license
- #Fsuipc prear3d setting free
Also note this profile is based off of the default profile and shouldn't have anything else in it, you do still need to make sure your gear and anything else are all bound within P3D as desired.īasically the way this works is that it emulates the same thing as pressing the default F1 and F4 bindings on your keyboard and then conditionally calls them a second time on the detents only when the reverser levers are pulled, which you can see if you look at the Lever 3/4 Commercial Reverser and Lever 3/4 Detent in the configurator with this profile loaded. If you find something wrong happening, simply reset the reverser handles and move the levers up a small amount (outside the detent) and down back to idle and it will reset it back to normal. You should also notice that the detents will only work when the reverser handles are pulled, but no other edge case is currently covered as how I set this up assumes you're going into the detents only with the reverser handles pulled. If you already have P3D open, from the menu bar go to Add-ons->Honeycomb->BFC_Throttle - Reload Bindings.įrom there, open P3D and the FSLabs and if you move the throttle levers around you should notice the reversers work. Make sure you load the profile (Profiles->select the profile->Load) and then activate it (Actions->Activate Current Profile). In configurator, from the top menu bar, go to Actions->Open Settings->Import Profiles and select the JSON file I have attached to this post. The installer should have created a shortcut on your desktop to access the configurator, if not you can find the binary for it in your P3D addons folder at the following path: Honeycomb/bin/honeycomb-configurator.exe
![fsuipc prear3d setting fsuipc prear3d setting](https://i.ibb.co/fXYMY7M/rudder.jpg)
![fsuipc prear3d setting fsuipc prear3d setting](https://live.staticflickr.com/65535/48984390943_8028f5cd2b_z.jpg)
#Fsuipc prear3d setting software
The only prerequisite is the Honeycomb Configurator software which you can get for your respective version of P3D here:
#Fsuipc prear3d setting free
This is also how just I managed to figure it out, if there is a better way please feel free to share.
#Fsuipc prear3d setting license
This is ideal for if you don't already have a license for FSUIPC. well that's a bad thing, not a good thing.This is something I just recently figured out after fighting to get it to work on my end for a number of days because of how the detents act as a button-press instead of part of the throttle axis, sharing for anyone else looking for a solution to this. These developers that say "Our aircraft doesn't need FSUIPC to work.". I hate this because I always like setting my controllers through FSUIPC with Profiles for each aircraft, but it is the only way I can get some of these aircraft that were not considering users that strictly use FSUIPC for their axis. My throttles work in the right direction as long as they are not going through FSUIPC. I don't even have to select reverse in P3D. Then enable joystick settings in P3D when flying that particular aircraft. I've had to actually shut off all axes settings in P3D and just use the throttle setting. If I try to go into "Joystick Settings" and click on the reverse box, my throttles won't work at all because these aircraft don't seem to allow any processing by FSUIPC. I set up my Aerosoft A330 and FSL A320 using this type of setting and my PFC throttles move backward. I am finding that these settings, going through FSUIPC as "Send to FS as normal axis" don't seem to work the same as default P3D. You can assign the throttles in fsuipc to use the default P3D control calibration instead of the fsuipc calibration (this works the same as if you assigned them in the P3D settings menu). You would then use the calibration tool in the P3D settings to assign the range of axes. How then can I have a mixed set up so that Prepar3d processes just the throttles? I would appreciate any advice you can give. I thought you had to choose between Prepar3d and FSUIPC and use one or the other. My Joystick Controllers are currently disabled in Prepar3d, so surely I would have to enable them so I can process the throttle? But this would enable all of the other axes which are currently handled by FSUIPC.
#Fsuipc prear3d setting how to
I don't understand how to set up the throttle axes in Prepar3d while everything else is handled by FSUIPC.
![fsuipc prear3d setting fsuipc prear3d setting](https://i.imgur.com/RHPHT8R.jpg)
I have heard that the Flight1 King Air doesn't like having the throttles processed through FSUIPC and that it is best of these are set in Prepar3d. I assign and calibrate all of my axes through FSUIPC. One of my main aircraft is Flight1's King Air B200, however the throttles on this aircraft are difficult to manage and I find that the engine number 1 spikes constantly when on the ground, which means that taxing is tricky.